displacement curve造句
例句與造句
- This function describes the envelope of the displacement curve .
這函數描繪出位移曲線的包絡。 - The calculation of these velocity and displacement curves from the accelerogram is not a trivial matter .
要從加速度記錄計算速度和位移曲線也不是一件輕而易舉的事。 - The force and displacement curves were obtained
得到了空氣彈簧橫向剛度特性的曲線圖。 - Before design cam , the tappet displacement curve has to be design
在設計凸輪之前，首先進行挺柱升程曲線的設計。 - According to the tappet displacement curve , the design of cam profile can be carried out by " reversal method " theory
根據得到的挺柱升程曲線，利用“反轉法”的原理進行凸輪輪廓曲線的設計。 - It's difficult to find displacement curve in a sentence. 用displacement curve造句挺難的
- And we measure the voltage ? displacement curve through examinations which can provide theoretics for the transducer ’ s use in mechine
在機械方面,提出了cymbal換能器堆疊結構,并測量了其電壓位移特性。 - When rotating into force , in accordance with the cam roller set displacement curve effort rotating turret , while the ramps along the rib rolling
當入力軸旋轉時，凸輪滾子按照設定的位移曲線旋動出力轉塔，而同時又沿肋的斜面滾動。 - The formation and formation reason of inertial force during the impact tests were studied by the force - displacement curve to determine the inertial force
摘要利用儀器化動態沖擊機測試力位移曲線，研究了沖擊過程中慣性力的產生，并分析了其產生原因，以確定慣性力。 - The loading - displacement curve was consistent with the loading - energy curve , and the both could explain the whole dynamic course and the phenomena of dynamic instability
結構的荷載一位移曲線與荷載一應變能曲線具有一致性，都能體現結構的動力變化過程和解釋動力失穩的現象。 - Comparison of these two methods was completed by comparing the displacement curve and the velocity curve . strongpoint and demerit of each method were concluded
通過幾次試驗的對比分析,其中包括目標彈的位移曲線和速度曲線的對比,充分證明了兩種方法的可行性并指出各自的優缺點。 - A corresponding program is developed . nonlinear load - displacement curve in complete - process analysis of a double - layer reticulated shell structure is traced out by the program
研制了相應有限元程序,對網殼結構進行非線性的荷載?位移全過程跟蹤分析,得到網殼結構荷載?位移全過程曲線。 - The load displacement curves and the ultimate strength of each member are presented . effects of beam length , radius of curvature and flexural - torsional rigidity on ultimate are considered
通過試驗研究，給出每個構件的荷載位移曲線和極限承載力，得到了曲梁承載力隨跨長、曲率半徑以及截面尺寸的變化規律。 - The paper ' s design mainly includes two parts . fist part is the tappet displacement curve ' s design , and many dynamics calculation has to be done based on the dynamic design . second part is to design cam profile curve
本文的設計主要包括兩大部分，第一部分為挺柱升程曲線的設計，按照動態設計要進行大量的動力學計算，第二部分是凸輪輪廓曲線的設計。 - The load - displacement curves and moment - curvature curves that calculated from the full - course analysis program are in accordance with the resuits of experimental especially in prime period of ioad presents the program is avaiiable
試驗和全過程分析得到的荷載-撓度曲線對比表明：在加載前期兩者的曲線吻合較好，證明全過程分析能反映碳纖維加固梁的受力特點及程序的正確性。 - With the modeling method in this paper , it is showed that numerical load - displacement curves agree well with the experimental skeleton curves , and that the errors of crack load are bigger , but the cra
分析表明：采用本文的建模方法，計算所得的荷載?位移曲線與試驗所得的骨架曲線符合較好；開裂荷載有的誤差較大，但開裂部位及過程與低周反復荷試驗中某一方向加載所得的結果較為符合。
更多例句： 下一頁